OSHA requires every forklift to be examined before it is placed in service, at least daily, and after each shift where trucks run around the clock (29 CFR 1910.178(q)(7)). It does not say how. In a 2000 letter of interpretation, OSHA said the check does not even have to be written on a checklist. The method is yours to choose, and there are three common ones: paper, an app, or a check built into the truck that locks it out until the check is done.
All three ask the operator the same questions. They differ in what happens on an ordinary shift, when the operator is in a hurry and the truck is needed now.
What any daily check has to do
Whatever the method, a daily check program has five jobs:
- Ask the right questions for that truck. An electric reach truck and a propane counterbalance truck do not fail in the same places.
- Get the answers before the truck goes to work, not at the end of the shift.
- Keep a truck that fails out of service. OSHA says a truck with a condition that affects its safety is not placed in service, and one that is unsafe is taken out of service until it is repaired ((p)(1)).
- Tell someone who can fix it. OSHA’s guidelines say defects are reported and corrected immediately.
- Leave a record you can find later, with a name on it.
Who does what
Those jobs fall to two people, and a program only works when both do their part. Management’s side:
- Make the workplace safe to drive in, and keep it that way.
- Make sure every operator is trained and evaluated before they drive ((l)(1)).
- Take any truck that is unsafe or needs repair out of service, and keep it out until it is fixed.
- Keep the results where they can be found. OSHA’s guidelines do not require a written record, but without one there is no way to show the check was done.
The operator’s side:
- Do the check before the truck goes to work.
- Record what was found, in whatever form the site uses.
- Report anything unsafe to a supervisor straight away.
- Drive the truck safely.
The point of all of it is a safe place to run equipment, free of the accidents that come from a truck that should never have been driven. Each method below leaves a different share of those jobs to people remembering.
Hold each method up against the five jobs.
Paper
A printed sheet on a clipboard, one line per question, initialed by the operator. OSHA’s sample daily checklists for engine and electric trucks are a common starting point.
Paper costs almost nothing, needs nothing installed and works in any building. Its weak points are jobs two to five. The truck starts whether the sheet is filled in or not, so sheets can be filled in late, or several days at once. A failed item is only reported if someone reads the sheet that day. And finding who checked truck 4 on a Tuesday three months ago means going through a box.
Paper fits a small fleet on one shift, with a supervisor who reads every sheet before the trucks go out.
A checklist app
The same questions on a phone or tablet. The answers are stored in the app under the user who signed in, and reports can be exported without anyone typing up sheets.
An app does the fifth job far better than paper, and it is the quickest way off paper: you can start today with the phones you already have. Its weak points are the second and third jobs. An app is not wired to the truck, so it cannot stop one from starting. A truck that fails in the app can still be driven, and the check depends on a phone being within reach and charged. The record also shows whoever was signed in on the device, which is not always the person who drove.
An app fits if you inspect many kinds of things, not only vehicles, or if nothing can be wired into the trucks.
Lockout: the check built into the truck
Here the check is on the truck itself. The Start-Manager SM301 is wired in place of the key. The operator enters their own code or presents their card, the questions appear on the unit’s screen in random order, and the truck will not start until they are answered. If a question fails, the truck can stay locked until a supervisor releases it. Every check goes to the web portal under the operator’s name, and reports can be emailed on a schedule.
This is the only one of the three that can do the second and third jobs on its own, because the truck itself waits. It also controls who can start each truck, and after an accident it shows who was on it.
It has limits too. Each truck needs its own unit, bought and installed. The portal needs your Wi-Fi, though the unit keeps every check until it is back in range. And no system can make an operator look at the tires: someone determined to press pass on every question still can. What lockout changes is that the check cannot be skipped or filled in later, and every answer is tied to the code or card that started the truck.
A test to run on your own method
Pick one truck and one day from last month. Then try to answer four questions from your records alone:
- Who checked it, and were they trained on that type of truck?
- Was the check done before the truck went to work?
- Did anything fail, and who was told?
- Was the truck kept out of service until it was fixed?
If any answer is “we think so”, that is the gap to close, whichever method you use.
You can mix them
These are not all-or-nothing. Nothing stops you keeping an app for inspections that have nothing to do with starting a truck, such as racking, dock plates or fire extinguishers, and putting the lockout check on the trucks.
For prices side by side, see our electronic forklift checklist comparison. For building the program around whichever method you choose, see how to implement a daily safety check program, and for what an OSHA inspector will ask, what the renewed warehouse inspection program means for daily checks. To try the lockout check on one truck first, there is the Introductory Offer.
The next step is a one-hour online demo. Book one here.
Make your safety checks easy
Call us 1-800-674-9320 or book a walkthrough of the system.